| Author |
 Topic  |
| |
Current Topic Rating:  | Join the Forum to Rate this Topic at: www.VNCommodore.com Support Forums
|
|
|
wayneo7
Learner
7 Posts
 |
 Posted - 20 Oct 2007 : 09:56:17 AM
|
Hey buddy`s
took my vp rof a run this morning and used win aldl to log it for the first time , but i really cannot inturpret any of the codes or data that came out of it  , can anyone help ? the data is attached .
cheers yall
Time SENSOR:PROMID SENSOR:IAC SENSOR:Coolant Temp SENSOR:SPEED SENSOR:MAP SENSOR:RPM SENSOR:TPS SENSOR:INT SENSOR:O2 SENSOR:Battery Voltage SENSOR:Knock counter SENSOR:BLM SENSOR:rich / lean counter MW2:Vss Pulse Occured MW2:ESC 43B Ready for second Pwr Enrich MW2:DRP Occured MW2:Factory Test Mode (3.9k Ohms MW2:Diagnostic Mode (0 Ohms) MW2:ALDL Mode (10k Ohms) MW2:1st time Idle Flag / High Bat Voltage MW2:Idle / Cool Flag MWAF1:Clear Flood Flag / Not Closed Loop MWAF1:BLM Enable Flag MWAF1:Low Battery (IAC Inhibited) MWAF1:4-3 Downshift for TCC unlock MWAF1:Asynchronous Fuel Flag MWAF1:Old High Gear Flag MWAF1:Rich Flag MWAF1:Closed Loop Flag MCU2IO:AIR Divert Solenoid ON MCU2IO:AIR Divert Solenoid ON MCU2IO:A/C Disabled MCU2IO:TCC Locked MCU2IO:Park/Neutral MCU2IO:No High Gear MCU2IO:Not Used MCU2IO:No A/C Requested MALFFLG1:24 VSS (Vehicle Speed Sensor) MALFFLG1:23 IAT / MAT low (Air Temperature) MALFFLG1:22 TPS low (Throttle Position Sensor) MALFFLG1:21 TPS high (Throttle Position Sensor) MALFFLG1:15 CT low (Coolant Temperature) MALFFLG1:14 CT high (Coolant Temperature) MALFFLG1:13 Oxygen sensor MALFFLG1:12 Engine not running MALFFLG2:42 EST (Electronic Spark Timing) MALFFLG2:41 Not Used MALFFLG2:35 Not Used MALFFLG2:34 MAP low (Manifold Air Pressure) MALFFLG2:33 MAP high (Manifold Air Pressure) MALFFLG2:32 EGR (Exhaust Gas Recirculation) MALFFLG2:31 Governor Fail MALFFLG2:25 IAT / MAT high (Air Temperature) MALFFLG3:52 CAL Pack missing MALFFLG3:53 Not Used MALFFLG3:54 Fuel Pump Relay Faliure MALFFLG3:55 ADU error MALFFLG3:51 PROM error MALFFLG3:45 O2 rich (Oxygen sensor) MALFFLG3:44 O2 lean (Oxygen sensor) MALFFLG3:43 Knock ESC
|
|
Report to Moderator |
|
|
nodg
National Driver
1667 Posts
|
Posted - 20 Oct 2007 : 10:57:53 AM
|
| i dont understand any of the codes and there only seems to be codes for some of the sensors and some are left blank?? and what about the errors at the end of the script? read the helpfile and i think it will give you a better idea. |
Cheers,
Nodg. |
Report to Moderator  |
|
|
wayneo7
Learner
7 Posts
|
Posted - 20 Oct 2007 : 11:42:17 AM
|
| i recon hey i see all those errors and wonder how the car is still running ? and running great at that ? |
| Report to Moderator |
|
|
nodg
National Driver
1667 Posts
|
Posted - 20 Oct 2007 : 12:15:35 PM
|
| it may not be a permanant problem it could be every now and then for only a second |
Cheers,
Nodg. |
| Report to Moderator |
|
|
wayneo7
Learner
7 Posts
|
Posted - 20 Oct 2007 : 12:19:45 PM
|
yeah sound like it would be cause the car runs fine . you know anything about the knock count ? cause it is up to 133 ? dunno if thats how meny time the engien knocked or if it be just a load of craphola. |
| Report to Moderator |
|
|
nodg
National Driver
1667 Posts
|
Posted - 20 Oct 2007 : 12:34:34 PM
|
| im not entirely sure but 133 times sounds a bit too much is the engine fully serviced? get a tune, use some good fuel and make another run cause although its normal for your engine to knock when its clocked up a few kays, and the sensor is acknoledging that but couldnt be a faulty knock sensor, or just the tuning. |
Cheers,
Nodg. |
| Report to Moderator |
|
|
wayneo7
Learner
7 Posts
|
Posted - 20 Oct 2007 : 9:36:18 PM
|
hey bro ,
yeah i service it myself , every 5000 k`s oil , filter , air ect..(i use to own a rotory)(force of habit) i run 8mm leads and bosch 4 sparke |
| Report to Moderator |
|
|
nodg
National Driver
1667 Posts
|
Posted - 21 Oct 2007 : 7:16:15 PM
|
| Replacing the sensors on the motor will resolve some of the issues listed, but try and work out what all the info means! |
Cheers,
Nodg. |
| Report to Moderator |
|
|
trizo
Forum Moderator
3091 Posts
|
Posted - 21 Oct 2007 : 9:44:17 PM
|
lol even reset the ecm so it get rid of old faults that have been logged!
Win aldl is crap! |
3 can keep a secret if 2 are dead |
| Report to Moderator |
|
|
nodg
National Driver
1667 Posts
|
Posted - 22 Oct 2007 : 08:34:58 AM
|
| never used it but have a copy on my pc, for free software it isnt bad you just need to decipher it |
Cheers,
Nodg. |
| Report to Moderator |
|
|
mayhem2408
P Plater
11 Posts
|
Posted - 27 Oct 2007 : 5:06:13 PM
|
quote:
Originally posted by wayneo7
Hey buddy`s
took my vp rof a run this morning and used win aldl to log it for the first time , but i really cannot inturpret any of the codes or data that came out of it , can anyone help ? the data is attached .
cheers yall
Time SENSOR:PROMID SENSOR:IAC SENSOR:Coolant Temp SENSOR:SPEED SENSOR:MAP SENSOR:RPM SENSOR:TPS SENSOR:INT SENSOR:O2 SENSOR:Battery Voltage SENSOR:Knock counter SENSOR:BLM SENSOR:rich / lean counter MW2:Vss Pulse Occured MW2:ESC 43B Ready for second Pwr Enrich MW2:DRP Occured MW2:Factory Test Mode (3.9k Ohms MW2:Diagnostic Mode (0 Ohms) MW2:ALDL Mode (10k Ohms) MW2:1st time Idle Flag / High Bat Voltage MW2:Idle / Cool Flag MWAF1:Clear Flood Flag / Not Closed Loop MWAF1:BLM Enable Flag MWAF1:Low Battery (IAC Inhibited) MWAF1:4-3 Downshift for TCC unlock MWAF1:Asynchronous Fuel Flag MWAF1:Old High Gear Flag MWAF1:Rich Flag MWAF1:Closed Loop Flag MCU2IO:AIR Divert Solenoid ON MCU2IO:AIR Divert Solenoid ON MCU2IO:A/C Disabled MCU2IO:TCC Locked MCU2IO:Park/Neutral MCU2IO:No High Gear MCU2IO:Not Used MCU2IO:No A/C Requested MALFFLG1:24 VSS (Vehicle Speed Sensor) MALFFLG1:23 IAT / MAT low (Air Temperature) MALFFLG1:22 TPS low (Throttle Position Sensor) MALFFLG1:21 TPS high (Throttle Position Sensor) MALFFLG1:15 CT low (Coolant Temperature) MALFFLG1:14 CT high (Coolant Temperature) MALFFLG1:13 Oxygen sensor MALFFLG1:12 Engine not running MALFFLG2:42 EST (Electronic Spark Timing) MALFFLG2:41 Not Used MALFFLG2:35 Not Used MALFFLG2:34 MAP low (Manifold Air Pressure) MALFFLG2:33 MAP high (Manifold Air Pressure) MALFFLG2:32 EGR (Exhaust Gas Recirculation) MALFFLG2:31 Governor Fail MALFFLG2:25 IAT / MAT high (Air Temperature) MALFFLG3:52 CAL Pack missing MALFFLG3:53 Not Used MALFFLG3:54 Fuel Pump Relay Faliure MALFFLG3:55 ADU error MALFFLG3:51 PROM error MALFFLG3:45 O2 rich (Oxygen sensor) MALFFLG3:44 O2 lean (Oxygen sensor) MALFFLG3:43 Knock ESC
What you have here is only the column titles of the data file. The actual data is missing. As an example, you would have the first line with the titles followed by lots of data
Line1: SENSOR:RPM SENSOR:TPS SENSOR:SPEED
Line2: 1025 0 0
Line3: 2050 24 20
This would show The Engine RPM, The Throttle Position in % and the Road Speed in KPH.
I was writting a very advanced ALDL 160Baud reader a couple of years ago, but limitation in the 160 baud protocol caused me to stop development and start working on a newer ALDL 8192baud reader. This is still in development. If anyone wants the ALDL160 software, I will email it do you an no cost. I can't work out how to attach it on this forum.
 |
| Report to Moderator |
|
|
nodg
National Driver
1667 Posts
|
Posted - 28 Oct 2007 : 12:15:56 AM
|
| looks very interesting, that program is worth a bit to me i wouldnt mind a copy, my email adress is hsv_gts_v8@hotmail.com , also i hear you can make up a usb to aldl connecter from parts found at dick smiths?? or if the cable itself is cheap and easily acsesible then where could i source one? |
Cheers,
Nodg. |
| Report to Moderator |
|
|
VNSVLE
Forum Moderator
1316 Posts
|
Posted - 28 Oct 2007 : 10:16:57 AM
|
| Wouldn't mind having a play with that myself mayhem. Email - euranth@hotmail.com |
What's the difference between understeer and oversteer?
Understeer is when the driver is scared.
Oversteer is when the passenger is scared. |
| Report to Moderator |
|
|
jas89
Forum Moderator
779 Posts
|
|
|
David
The Guru
334 Posts
|
Posted - 28 Oct 2007 : 4:34:37 PM
|
If you would like for me to put it up for you, I can do that if you want.quote:
Originally posted by mayhem2408
If anyone wants the ALDL160 software, I will email it do you an no cost. I can't work out how to attach it on this forum.
I have sent you an e-mail to give you an e-mail address to send it to. |
Cheers,
David |
| Report to Moderator |
|
|
nodg
National Driver
1667 Posts
|
Posted - 01 Nov 2007 : 2:42:27 PM
|
| i got a copy sent to my hotmail address but it wont download!! can someone post it up on the site??? |
Cheers,
Nodg. |
| Report to Moderator |
|
|
jas89
Forum Moderator
779 Posts
|
Posted - 01 Nov 2007 : 7:22:59 PM
|
quote:
Originally posted by nodg
i got a copy sent to my hotmail address but it wont download!! can someone post it up on the site???
yeh same hear aswell...just tried it |
|
| Report to Moderator |
|
|
f8tal02118
P Plater
72 Posts
|
|
|
MILD50
Fully Licenced
850 Posts
|
Posted - 02 Nov 2007 : 08:51:12 AM
|
PM sent mate.
This should be a good little tool to have. |
| Report to Moderator |
|
|
wayneo7
Learner
7 Posts
|
|
|
blu vn grp a
Starting in the driveway
2 Posts
|
Posted - 15 Nov 2007 : 4:16:45 PM
|
hi guy`s if you look at the ecm in your car & then go to the (win ALDL ) main screen up the top of main it says configuration click on that. then at the top use the up or down to match the ecm with yours so the programme is matched to the rite settings. then have fun with it
cheers
blu vn grp a
true blu
paul |
| Report to Moderator |
|
|
nodg
National Driver
1667 Posts
|
Posted - 01 Dec 2007 : 2:19:11 PM
|
at idle in tuner pro RT-
PROM ID- 7894.00-5525.00
Throttle pos- 0.71 volts
I.A.C- 0 steps- occasinal 1 step
EGR duty cycle- 25.78-27.34 DC
Engine speed- 850-950 rpm
Base pulse correction- 7-8 counts maximum
02 sensor- 728.16mv
knock count- varies from 0 straight to 128 continously
BLM- 0
02 cross count- 0 crosses
airflow- 32.12-36.08
base pulse width- 582.04-835.95
02 loop status at idle- open and closing every 10 seconds
rich/lean- varying between rich and lean continuously
learn control at idle is on and off at random
IN WINALDL-
number 20 flashing at top of screen in green- blm, int and 02 sensor pages are flashing green boxes in 800 rpm boxes on the- 30 and 40 range.
no error codes present
RAW DATA-
PROMID- 7894-5525
I.A.C- 0-1 at random
MAP sensor- 67-70 fluctuating at random values- converted value-1.3volts
TPS- 36-37- converted value- 0.73 volts
IFR- 7-8 converted value- 0.59-0.67
BLM- 1 and 132
02 sensor- 199-200-204-205
battery voltage- 128-129- converted 12.8-12.9 volts at idle
INT- 0 and 128
who can diagnose this for me as its my first time using winaldl, also its a v8 if thats matters! all the values are at idle at normal operating temperature. i can decipher some of it but dont know the default voltages and stuff are normally and if they are continuoulsy changing values. any help would be great! |
Cheers,
Nodg. |
| Report to Moderator |
|
|
Magic-Man
Starting in the driveway
1 Posts
|
Posted - 05 Dec 2007 : 3:24:10 PM
|
Wicked software.
Could I get a copy please.
Thanks in advance
Michael |
| Report to Moderator |
|
|
David
The Guru
334 Posts
|
Posted - 05 Dec 2007 : 3:48:19 PM
|
| If you login as your member to the forum, I have a link to the software. |
Cheers,
David |
| Report to Moderator |
|
|
nodg
National Driver
1667 Posts
|
Posted - 05 Dec 2007 : 5:12:44 PM
|
| i still cant get the software to work but if i could then i would praise it alot more |
Cheers,
Nodg. |
| Report to Moderator |
|
|
Richo7502000
Learner
9 Posts
|
|
|
Stormwalker
Starting in the driveway
1 Posts
|
|
|
MILD50
Fully Licenced
850 Posts
|
Posted - 15 Feb 2008 : 2:12:41 PM
|
quote:
Originally posted by David
If you login as your member to the forum, I have a link to the software.
Can be downloaded from the member's section guys. |
| Report to Moderator |
|
|
mike
Learner
6 Posts
|
Posted - 24 Mar 2008 : 12:36:09 PM
|
quote:
Originally posted by MILD50
quote:
Originally posted by David
If you login as your member to the forum, I have a link to the software.
Can be downloaded from the member's section guys.
Is there some place to get the connector to plug into the output in my VN, and can I adapt this to a laptop that only has usb? cheers
i have been keeping my old Vn alive for long while, bullet proof, just got an old VR also, so shall find new things of other s problems to learn about and improve along the years. |
| Report to Moderator |
|
|
nodg
National Driver
1667 Posts
|
|
|
nodg
National Driver
1667 Posts
|
Posted - 24 Mar 2008 : 4:01:28 PM
|
| http://www.techedge.com.au/vehicle/aldl160/aldl_hw.htm, a bit complicated but if you have some knoe how and want to run around looking for parts go for it, but you can find them on ebay for 60 dollars including postage. now ive got an adaptor off ebay as well to use my laptop but it takes a driver and some tweaking to get it working. |
Cheers,
Nodg. |
| Report to Moderator |
|
|
Topic |
|
Topic Locked
